Choose your file, place your engraving material into the machine, close the door and press GO. The laser will take care of the rest.
Laser cutting can be used in both small- and large-scale manufacturing.
There are three types of laser cutting that exist. These are sublimation cutting and fusion cutting.
Before starting the machine every day, carefully check the pressure of the working gas and cutting gas. If the gas pressure is not enough, it should be replaced in time. Check whether the zero points of X axis, Y axis, and Z-axis, laser ready state and other buttons are damaged. Check whether the zero point, limit switch, and travel block mounting screws of the X axis, Y axis, and Z axis are loose, and whether the limit switches of each axis are sensitive. Check whether the circulating water level in the chiller is sufficient. If it is insufficient, it must be replenished in time. Check whether there is leakage of the circulating water in the external optical path, and the leakage must be dealt with in time, otherwise the life of the optical lens will be affected. The cutting waste should be cleaned up in time, the workplace should be cleaned up, and the workplace should be kept clean and tidy. At the same time, do a good job of cleaning the equipment to ensure that all parts of the equipment are clean and free of stains, and no debris can be placed in each part of the equipment.After the daily work is completed, open the drain valve of the air storage tank at the bottom of the air compressor to drain water, and close the drain valve after the waste water is discharged. After the daily work is completed, shut down according to the shutdown steps, and then turn off the main power of the entire machine.
Laser cutting can be achieved using high-power density energy from a focused laser beam. The CNC controller controls the laser generator to produce a high-frequency pulsed light beam in a controlled manner. This laser generates a beam of a specific frequency and width. The laser beam is transmitted through the optical path, reflected back into the optical path, and then focused by the focusing group. The focal point is located close to the surface to be cut. A small, high-energy, dense light spot forms on the part's surface. Material melts or vaporizes instantly. Each laser pulse creates a tiny hole in the substrate. The computer numerical controller controls the laser head and substrate to perform relative movement and dotting in accordance with the design file. This allows the substrate to be cut into the desired shape.
Are you trying to find the best budget machine for laser cutting?
Waveguide laser tubes from GSS Machinery are the most advanced in the field. GSS Machinery laser tubes offer the best engraving and cutting results. They have faster switching rates, higher CO2 gas pressure and an optimized beam.
Debug your equipment again and adjust the focus of the cutting head so that it is in the correct position.
Lasers can engrave high-resolution graphics at high speeds thanks to the incredible motion control in our laser machines. It will allow you to create images that will truly amaze your customers.
You should pay special attention to the core parts of your machine, including laser generator, cutting head and servomotor, guide rail, water cooler, and others. These parts will impact the machine's accuracy and cutting speed.
No matter what material you need to be cut, such as hardwood, plywood, mdf and basswood, leather or fabric, or paper or cardboard, there is a laser cutter for you.
Laser cutter is an automated laser tool that includes CNC controller and machine frame. It also includes power supply, laser tube and laser head.
This machine can cut wood, paper, acrylic and leather that's 5mm thick or less, and offers a maximum engraving size of 100x2000mm. It's packed with safety features, too, including a protective shield, goggles, over-heating protection, password lock, motion detection, laser indicator and overheat shut down.
A red light positioning system make it easier to accurately line up your materials, plus a suspension system immediately halts the laser whenever you open the doors. Speaking of doors, the front and rear double doors allow you the space to engrave materials of any length. There's also a ventilation fan for exhaust smoke, and a display that shows you the cooling water temperature for safety.
Polycarbonate is an unsuitable material for laser cutting. ABS It emits cyanide gas and melts. ABS is difficult to cut with a laser cutter. It melts rather than vaporizes, and it is more likely to catch fire and leave melted gooey deposits on the vector cutting grid.
Thickness: A 40W to 45W CO2 laser, such as the Muse Core or 3D autofocus, can generally cut up to 14" thick wood, whereas a 90W tube laser, such as the P-Series PS24 or Muse Titan, can cut up to 12" thick wood.
Laser Cutting Process Drawbacks
When compared to other techniques, laser cutting requires a high power consumption.
The laser beam is extremely delicate to handle.
If the laser beam comes into contact with human workers, it is hazardous.
Laser cutting is still unable to cut thick metals.