How To Become A Sidemount Technical Scuba Diver Harness

What is the difference between rebreather and non rebreather mask

It takes passion, experience, and training to become a technical dive instructor. Technical diving comes with additional risks, so it's not worth taking on if you don't have the right combination.

The technical sidemount was completed the next day. This involved adding our 50-percent oxygen tank and 100 percent oxygen tanks to either side. This will increase your profile underwater. You must ensure that the tanks are as slim as possible. A couple of clips are located on either side of your waist. When your tanks become positively buoyant and you inhale, adjust the clip to match your tank position. It is important to keep your breathing as smooth as possible. Your breathing will change from one tank to another every few minutes. The pressure in each tank will drop at approximately the same rate. If a regulator or tank fails, you will still have gas to breath. Comfort and enjoyment can only be achieved by gaining experience. I spent the next few day doing deco dives using the sidemount rig with Evolution co-owner David Joyce, a Trimix instructor and Tec diver. We visited the Japanese Mogami wreck at 164ft, where I was charmed by the pieces of old gas masks and uniforms.

There are three parts to certification: knowledge development, skill practice and open water dives. You can complete all three parts locally, on holiday, or split between the two.

To extend their time at the wrecks and reefs below the ocean floor, decompression divers use oxygen mixtures. Decompression divers can cruise around the ocean floor for as long as 60 minutes, whereas sport divers may only be able to do two bottom dives at 100ft for 15 minutes each.

Cylinder

The Sidemount diving setup is a little different from the setup when diving backmount and so is the equipment.

Computer-aided instruction is an integral aspect of almost all courses we teach. The Why? The simple answer is that eLearning allows students to get in the water faster and spend more time there. This is why we include any applicable eLearning program -- typically a $140 value -- in all our courses at no extra cost. This is equivalent to an additional day's in-water training. This is what it's worth. Priceless.

Cylinder
Scuba Tank

Scuba Tank

The very general definition of technical diving is to be exposed to a ceiling that does not allow a diver to ascend to the surface at any moment of the dive. This might be due to a real ceiling, in terms of a cave or a wreck, or a virtual ceiling created by a decompression obligation. In this case, by exceeding the NDL’s, mandatory decompression stops have to be performed on ascent in order to avoid any case of decompression sickness. In most cases this requires the use of special equipment, e.g. Twinsets or Sidemount, special gas mixes and of course additional training to be able to perform those stops accurately on ascent to optimize off-gassing of Nitrogen.

There are two options available with most agencies: technical Sidemount or recreational Sidemount. Similar prerequisites apply to both TDI or SDI. However, the tec-sidemount course will increase your skills. The course will also require you to learn more about them. Perfect trim and maintaining your level during the skill development is a must.

How To Become A Sidemount Technical Scuba Diver Harness

Where are bodies from Titanic

There are three parts to certification. Knowledge development, skill practice and open-water diving. You can do all three on your own, or take a break to complete one of them.

Skills (generally applicable) - The introductory tech dive will practice their buoyancy and trim with the new equipment configuration. This will help you to dive efficiently. Once this foundation has been established, students can practice locomotion to improve their skills.

Thailand
Thailand

The Sidemount diver's setup is slightly different than the backmount.

Sidemount cylinder mounting originated for cave diving and have become more popular in all forms of technical diving since. They separate the dual cylinders, with a 1st stage on each cylinder, and mount them on either side of the diver’s body. This doesn’t allow the diver to breathe from either cylinder in the event of a regulator failure, but does give the diver easier access to valves. Sidemount diving gives the diver a larger horizontal profile, but a smaller vertical profile.

How To Become A Sidemount Technical Scuba Diver 40 Ft

Specific Skills - These are the skills required to perform specific types of diving. Navigation and line skills are developed until they are effortless for overhead diving. Decompression divers have the ability to execute stops and gas management plans without a blink of an eye. Rebreather divers test, build and then disassemble their equipment meticulously to ensure it works properly. Each course requires skills that are established at the initial level. Then, it is possible to move on to higher levels. Each step further or hones these skills, and adds more challenges to make a diver well-rounded and knowledgeable.

Do you want to become a Sidemount diver. You've come to the right spot, as this article will cover all the details!

Check our other pages :

Frequently Asked Questions

Have a PADI Deep Specialty Instructor certification or have completed a PADI Deep Specialty Instructor course. Have at least 100 logged dives, including at least 20 enriched air dives, 25 dives deeper than 18 meters/60 feet, and 15 dives deeper than 30 meters/100 feet. You can become a Tec 45 diver.
 

5-6 days
Rebreather training classes are typically 5-6 days long, but can be longer depending on a variety of factors such as the training agency, your local conditions, your instructor, and your ability to meet the class standards.

2-3 hours
Even with small cylinders, you can usually dive for 2-3 hours (rebreathers typically have two 2/3l cylinders or one 3/5l cylinder).